Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
Almost everyone seems to have their own unique way of thinking on the subject of Tools You Need to Install a New Bathtub .
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of working with a service provider to take over a halfway-completed job, it is much better to take into consideration employing one before you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new tub in your bathroom if you have actually already gotten a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices and also product list need to comprise the following:
Preparing for the Installation
First of all, the supporting framework supplied with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and check all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and also examine the overflow outlet as well as the typical electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will settle it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our part on How to Install a Bathtub Yourself. Thanks a ton for taking a few minutes to read through our post. Loved our review? Please share it. Let other people locate it. I am grateful for your time. Don't hesitate to come by our site back soon.
Click Here
Report this page